Attributes

Combination options bQ x bL	400 x 400; 480; 640,480 x 400; 480; 640,640 x 400; 480; 640,800 x 400; 480; 640
Conveyor medium	Toothed belt (suitable for use in an EPA)
Delivery information	Assembled,Kit for electric position sensor included,Kit for protective case included
ESD	Yes
Motor connection [AT]	S = Kabel/Stecker,K = Klemmenkasten
Nominal speed [vN]	0 m/min ohne Motor und ohne Getriebe,6 m/min,9 m/min,12 m/min,15 m/min,18 m/min
Notice	Pneumatic equipment PN = 2: upper and middle lift position,Pneumatic equipment PN = 3: upper, middle and lower lift position
Pneumatic straight connection [Ø]	6mm
Preferred values	400480640800
Recommended accessories	Damper DA 2/100-B for outfeeding workpiece pallets WT 2, WT 2/F, WT 2/H or WT 2/F-H, required when v<sub>N</sub> <gt/> 12 m/min or total weight of the workpiece pallet ≥ 30 kg,Rockers WI 2/…, WI/M and damper DA 2/100-C for infeeding the workpiece pallets WT 2 and WT 2/F
Required accessories	1x sensor M12x1 with rated switching distance S<sub>N</sub> = 4 mm for each position sensor
Reversible operation [RV]	Reversierbetrieb möglich
Scope of delivery	Incl. fastening material,Pneumatic equipment for 2 or 3 positions,Assembly kit for electrical position sensor,Protective case
Weight	0kg
Workpiece pallet weight [mG]	50kg
required compressed air connection [pmax]	6bar
required compressed air connection [pmin]	4bar

• Lift transverse unit for feeding out of a from longitudinal section into a transverse section and vice versa
• Use in tight spaces by means of suspended drive motor (outside dimensions must be no wider than the section)
• Reinforced version of HQ 2/U with two lift cylinders for large workpiece pallet dimensions
• Drive by toothed belt coupling is not possible because of the compact design
• Conveyor medium: Toothed belt (suitable for use in an EPA)
• Pneumatic equipment for 2 (top, center) or 3 (top, center, bottom) lift positions
• Suitable for mounting on an ST 2/… section with a profile width of 45 mm or an ST 2/…-H section with a profile width of 50 mm
• Can be combined with WT 2, WT 2/F, WT 2/H, WT 2/F-H and WT 2/LS (only with version LS)
• Reversible operation possible
• 1 - Lift transverse unit for feeding out of a from longitudinal section into a transverse section and vice versa
• 2 - Use in tight spaces by means of suspended drive motor (outside dimensions must be no wider than the section)
• 3 - Reinforced version of HQ 2/U with two lift cylinders for large workpiece pallet dimensions
• 4 - Drive by toothed belt coupling is not possible because of the compact design
• 5 - Conveyor medium: Toothed belt (suitable for use in an EPA)
• 6 - Pneumatic equipment for 2 (top, center) or 3 (top, center, bottom) lift positions
• 7 - Suitable for mounting on an ST 2/… section with a profile width of 45 mm or an ST 2/…-H section with a profile width of 50 mm
• 8 - Can be combined with WT 2, WT 2/F, WT 2/H, WT 2/F-H and WT 2/LS (only with version LS)
• 9 - Reversible operation possible

Lift transverse unit HQ 2/U2 LS
Pneumatic equipment for 2 (top, center) or 3 (top, center, bottom) lift positions, Conveyor medium: Toothed belt (suitable for use in an EPA), Reversible operation possible, Suitable for mounting on an ST 2/… section with a profile width of 45 mm or an ST

• Data Sheet