Attributes

Productgroup ID	2
Workpiece pallet total weight [mG]	128kg
ESD	yes
required compressed air connection [pmax]	6bar
required compressed air connection [pmin]	4bar
Weight	0kg
Notice	Pneumatic equipment PN = 2: Upper and middle lift position,Pneumatic equipment PN = 3: Upper, middle and lower lift position
Scope of delivery	Incl. fastening material,Pneumatic equipment for two or three positions,Assembly kit for electrical position inquiry,Protective housing
Delivery information	Pre-assembled incl. pneumatic equipment,Protective housing, not assembled
Recommended accessories	Dampers DA 2/150-E, DA 2/100-E for outfeeding of the workpiece pallets WT 2, WT 2/F, WT 2/H or WT 2/F-H; required for v<sub>N</sub> > 9 m/min or total weight of workpiece pallet > 30 kg/cm,Rocker WI 2/…, WI/M and dampers DA 2/100-C for infieeding of the workpiece pallets WT 2 and WT 2/F
Required accessories	1x M12x1 sensor with rated sensing range S for each (top/bottom) position inquiry<sub>N</sub> = 4 mm,Adapter plate (available on request) required to mount a VA 2/D-130 perpendicular to the main direction of transport
Preferred values	240,320,400,480,640
Number of lifting cylinders	BG 1: 2,BG 2: 3,BG 3: 4

• Lift transverse unit for feeding out of a from longitudinal section into a transverse section and vice versa
• Use for high total weights up to 2 kg/cm on the smallest side of the workpiece pallet
• Sensor mounting for speed control during infeeding possible
• Lifting movements through two to four block cylinders depending on size
• Conveyor medium: Duplex chain (suitable for use in an EPA)
• Pneumatic equipment for 2 (top, center) or 3 (top, center, bottom) lift positions
• Suitable for mounting on an ST 2/… section with a profile width of 45 mm or an ST 2/…-H section with a profile width of 50 mm
• The lateral guides can be mounted on either the left or the right depending on the conveying situation
• Can be combined with WT 2, WT 2/F, WT 2/H and WT 2/F-H

HQ 2/U-H Lift Transverse Unit
Pneumatic equipment for 2 (top, center) or 3 (top, center, bottom) lift positions, Conveyor medium: Duplex chain (suitable for use in an EPA), Can be combined with WT 2, WT 2/F, WT 2/H and WT 2/F H, Suitable for mounting on an ST 2/… section with a profil

• 3D CAD
• Data Sheet

Required accessories

1x M12x1 sensor with rated sensing range S for each (top/bottom) position inquiryN = 4 mm

Adapter plate (available on request) required to mount a VA 2/D-130 perpendicular to the main direction of transport

Recommended accessories

Dampers DA 2/150-E, DA 2/100-E for outfeeding of the workpiece pallets WT 2, WT 2/F, WT 2/H or WT 2/F-H; required for vN > 9 m/min or total weight of workpiece pallet > 30 kg/cm

Rocker WI 2/…, WI/M and dampers DA 2/100-C for infieeding of the workpiece pallets WT 2 and WT 2/F

M12 sensor with M12x1 push-in fitting

M12 sensor with M12x1 push-in fitting

CAD data

M12 sensor with M8x1 push-in fitting

M12 sensor with M8x1 push-in fitting

CAD data

HQ 2/U-H Lift Transverse Unit

Note:

Adapter plate for mounting a VA 2/D-130 slide stop on the HQ 2/U-H perpendicular to the main direction of transport available on request.

Note:

Reversible operation possible Lateral guides of different heights allow for a fixed stop when outfeeding on the HQ

Combined with the HQ 2/U-H, only PE wear pads are recommended for use on the workpiece pallets.

Energy efficiency – Rexroth 4EE

Circuit diagram for unit with pneumatic equipment for two positions PN = 2, BG 1

bL < 320 mm

1)	Not included in the scope of delivery

Circuit diagram for unit with pneumatic equipment for three positions PN = 3, BG 1

bL < 320 mm

1)	Not included in the scope of delivery

Circuit diagram for unit with pneumatic equipment for two positions PN = 2, BG 1

bL ≥ 320 mm

1)	Not included in the scope of delivery

Circuit diagram for unit with pneumatic equipment for three positions PN = 3, BG 1, bL ≥ 320

1)	Not included in the scope of delivery

Circuit diagram for unit with pneumatic equipment for two positions PN = 2, BG 2

1)	Not included in the scope of delivery

Circuit diagram for unit with pneumatic equipment for three positions PN = 3, BG 2

1)	Not included in the scope of delivery

Circuit diagram for unit with pneumatic equipment for two positions PN = 2, BG 3

1)	Not included in the scope of delivery

Circuit diagram for unit with pneumatic equipment for three positions PN = 3, BG 3

1)	Not included in the scope of delivery

No.			3842998750
Max. total weight of workpiece pallet	mG	kg	128
ESD			yes
Reversible operation			Reversible operation possible
Required compressed air connection	p	bar	4 ... 6 bar
Pneumatic push-in fitting	Ø		BG 1, 2, 3: 6
			BG 3: 8

Compressed air consumption of TS 2plus units

Motor connection

Transport and nominal speed vN

Motor data

Cylinder arrangement