Attributes

Clean room classification	ISO class 7
Dry room	<lt/>1
ESD	Yes
Height	100mm
Length	250mm
Length max [L max]	5000mm
Length min [L min]	320mm
Motor connection [AT]	S = Kabel/Stecker,K = Klemmenkasten
Nominal speed [vN]	0 m/min ohne Motor und ohne Getriebe,6 m/min,9 m/min,12 m/min,15 m/min,18 m/min
Preferred values	80120160
Recommended accessories	Depending on the installation situation, additional accessories may be required for transportation control:,Damper DA 1,Switch Bracket,M12x1 Sensor with Rated Sensing Range of S<sub>N</sub>≥ 4 mm, Cannot be Installed Flush, but Rather with 0.5 mm
Required accessories	Two throttle non-return valves M5 for air intake throttling,Stop rail
Reversible operation [RV]	zulässig
Scope of delivery	Two lift transverse units, completely assembled,Belt Section BS 1/T,Two protective housings,Two mounting kits for the drive of the lift transverse units,Fastening material for installation between two ST 1 sections
Section load in accumulation operation	30kg
Weight	0kg
Width	200mm
required compressed air connection [pmax]	6bar
required compressed air connection [pmin]	4bar

• Section load up to 30 kg
• Lift cylinder – D = 25 mm
• Total stroke: 13 mm
• Motor mounting right (MA = R) or left (MA = L), with b = 160 mm also center (MA = M)
• Conveyor medium: Toothed belt with mesh top, suitable for use in an EPA
• Pneumatic equipment for 2 (top, center) or 3 (top, center, bottom) lift positions
• Motor connection optionally with cable/plug (AT = S) or terminal box (AT = K)
• Special models on request
• 1 - Section load up to 30 kg
• 2 - Lift cylinder – D = 25 mm
• 3 - Total stroke: 13 mm
• 4 - Motor mounting right (MA = R) or left (MA = L), with b = 160 mm also center (MA = M)
• 5 - Conveyor medium: Toothed belt with mesh top, suitable for use in an EPA
• 6 - Pneumatic equipment for 2 (top, center) or 3 (top, center, bottom) lift positions
• 7 - Motor connection optionally with cable/plug (AT = S) or terminal box (AT = K)
• 8 - Special models on request

Electrical transverse conveyor for connection of two longitudinal sections running in parallel with a distance between conveyors of more than 320 mm.
The electrical transverse conveyor EQ 1/T is used for connecting two parallel longitudinal sections with a distance between conveyors of = 320 mm. The belt section and the two lift transverse units share a common motor. It is also suitable for use in ESD applications. Accumulation operation on the belt section and reversible operation are allowed.
Conveyor medium: Toothed belt with mesh top, suitable for use in an EPA, Motor connection optionally with cable/plug (AT = S) or terminal box (AT = K), Special models on request, Section load up to 30 kg, Lift cylinder – D = 25 mm, Total stroke: 13 mm, Pn

• 3D CAD
• Data Sheet

Required accessories

Two throttle non-return valves M5 for air intake throttling

Stop rail

Stop Gate VE 1

Stop Gate VE 1

Pneumatic stop gate. When the pressure is released the stop gate is closed by a spring and the workpiece pallet is stopped. Tilting stop gate; can be opened without causing abrasion on the workpiece pallet stop surface. Permissible total load of all workpiece pallets in the accumulation: 80 kg (with conveying speed 9 m/min)

Assembly instructions

CAD data

Stop Gate VE 1/V

Stop Gate VE 1/V

Pneumatic stop gate. When the pressure is released the stop gate is closed by a spring and the workpiece pallet is stopped. Integrated solenoid valve enables short response times Tilting stop gate; can be opened without causing abrasion on the workpiece pallet stop surface. Permissible total load of all workpiece pallets in the accumulation: 80 kg (with conveying speed 9 m/min)

Assembly instructions

CAD data

Stop Gate, damped VE 1/D

Stop Gate, damped VE 1/D

Pneumatic stop gate. When the pressure is released the stop gate is closed by a spring and the workpiece pallet is stopped. Pneumatic damping can be adapted to the workpiece pallet weight Workpiece pallet minimum weight: 0.5 kg Permissible total load of all workpiece pallets in the accumulation: 12 kg (with conveying speed 6 m/min)

Assembly instructions

CAD data

Damper DA 1/A

Damper DA 1/A

Pneumatic damper Degree of damping adjustable Workpiece pallet load 0.5 kg to 6 kg permissible (with conveying speed 9 m/min)

Assembly instructions

CAD data

Switch Bracket SH 1/U

Switch Bracket SH 1/U

Assembly instructions

CAD data

Scope of delivery

Two lift transverse units, completely assembled

Belt Section BS 1/T

Two protective housings

Two mounting kits for the drive of the lift transverse units

Fastening material for installation between two ST 1 sections

Electrical Transverse Conveyor EQ 1/T

1)	Lift
2)	Protective housings
3)	Transport direction of longitudinal conveyor section
4)	Transport direction of transverse conveyor section

The electrical transverse conveyor EQ 1/T is used for connecting two parallel longitudinal sections with a section gap a > 320 mm. The belt section and both lift transverse units are powered by a shared motor. It is also suitable for use in ESD applications.

Accumulation operation on the belt section and reversible operation are permitted.

Energy efficiency – Rexroth 4EE

Circuit diagram for unit with pneumatic equipment for two positions PN = 2, BG 1

1)	Not included in the scope of delivery

Circuit diagram for unit with pneumatic equipment for three positions PN = 3, BG 1

1)	Not included in the scope of delivery

No.			3842998013
Max. section load in accumulation operation		kg	30
ESD			yes
Cleanroom class			ISO class 7
Dry room	r.F.	%	<1
Reversible operation			permitted
Required compressed air connection	p	bar	4 ... 6 bar
Length	l	mm	320 … 5,000