Attributes

Clean room classification	ISO class 7
Dimension drawing	1 Stroke,2 Protective cases,3 Conveying direction of longitudinal section,4 Conveying direction of transverse section
Dry room	<lt/>1
ESD	Yes
Motor connection [AT]	S = Kabel/Stecker,K = Klemmenkasten
Nominal speed [vN]	0 m/min ohne Motor und ohne Getriebe,6 m/min,9 m/min,12 m/min,15 m/min,18 m/min
Pneumatic circuit diagram	— • — Not included in the scope of delivery
Pneumatic straight connection [Ø]	4mm
Preferred values	80120160
Recommended accessories	Depending on the installation situation, additional accessories may be required for transportation control:,Damper DA 1,Switch Bracket,M12x1 Sensor with Rated Sensing Range of S<sub>N</sub>≥ 4 mm, Cannot be Installed Flush, but Rather with 0.5 mm
Required accessories	Two throttle non-return valves M5 for air intake throttling,Stop rail
Reversible operation [RV]	zulässig
Scope of delivery	EQ 1/TR, completely assembled,Protective housing,Fastening material for installation between two ST 1 sections
Weight	0kg
Workpiece pallet weight [mG]	3kg
required compressed air connection [pmax]	6bar
required compressed air connection [pmin]	4bar

• Available for belt distances a = 60 mm or a = 135 mm
• Lift cylinder – D = 25 mm
• Total stroke: 13 mm
• Conveyor medium: Toothed belt with mesh top, suitable for use in an EPA
• Pneumatic equipment for 2 (top, center) or 3 (top, center, bottom) lift positions
• Motor connection optionally with cable/plug (AT = S) or terminal box (AT = K)
• Special models on request
• 1 - Available for belt distances a = 60 mm or a = 135 mm
• 2 - Lift cylinder – D = 25 mm
• 3 - Total stroke: 13 mm
• 4 - Conveyor medium: Toothed belt with mesh top, suitable for use in an EPA
• 5 - Pneumatic equipment for 2 (top, center) or 3 (top, center, bottom) lift positions
• 6 - Motor connection optionally with cable/plug (AT = S) or terminal box (AT = K)
• 7 - Special models on request

Electrical transverse conveyor for connection of two longitudinal sections running in parallel with a small distance between conveyors.
The electrical transverse conveyor EQ 1/TR is used for connecting two parallel longitudinal sections with a small distance between conveyors. It is also suitable for use in ESD applications. Accumulation operation not permitted.
Conveyor medium: Toothed belt with mesh top, suitable for use in an EPA, Motor connection optionally with cable/plug (AT = S) or terminal box (AT = K), Special models on request, Available for belt distances a = 60 mm or a = 135 mm, Lift cylinder – D = 25

• 3D CAD
• Data Sheet

Connection Kit, Stop Rail

Connection Kit, Stop Rail

Assembly instructions

CAD data

Stop Gate VE 1

Stop Gate VE 1

Pneumatic stop gate. When the pressure is released the stop gate is closed by a spring and the workpiece pallet is stopped. Tilting stop gate; can be opened without causing abrasion on the workpiece pallet stop surface. Permissible total load of all workpiece pallets in the accumulation: 80 kg (with conveying speed 9 m/min)

Assembly instructions

CAD data

Stop Gate VE 1/V

Stop Gate VE 1/V

Pneumatic stop gate. When the pressure is released the stop gate is closed by a spring and the workpiece pallet is stopped. Integrated solenoid valve enables short response times Tilting stop gate; can be opened without causing abrasion on the workpiece pallet stop surface. Permissible total load of all workpiece pallets in the accumulation: 80 kg (with conveying speed 9 m/min)

Assembly instructions

CAD data

Stop Gate, damped VE 1/D

Stop Gate, damped VE 1/D

Pneumatic stop gate. When the pressure is released the stop gate is closed by a spring and the workpiece pallet is stopped. Pneumatic damping can be adapted to the workpiece pallet weight Workpiece pallet minimum weight: 0.5 kg Permissible total load of all workpiece pallets in the accumulation: 12 kg (with conveying speed 6 m/min)

Assembly instructions

CAD data

Damper DA 1/A

Damper DA 1/A

Pneumatic damper Degree of damping adjustable Workpiece pallet load 0.5 kg to 6 kg permissible (with conveying speed 9 m/min)

Assembly instructions

CAD data

Damper DA 1/B

Damper DA 1/B

Pneumatic damper Degree of damping adjustable Workpiece pallet load 0.5 kg to 6 kg permissible (with conveying speed 9 m/min)

Assembly instructions

CAD data

Switch Bracket SH 1/U

Switch Bracket SH 1/U

Assembly instructions

CAD data

Switch Bracket SH 1/S

Switch Bracket SH 1/S

Assembly instructions

CAD data

Switch brackets SH 1/M-A and SH 1/M-B

Switch brackets SH 1/M-A and SH 1/M-B

Setup from the half shells and in two versions possible Half shells: Polyamide; black

CAD data

Scope of delivery

EQ 1/TR, completely assembled

Protective housing

Fastening material for installation between two ST 1 sections

Electrical Transverse Conveyor EQ 1/TR

1)	Lift
2)	Protective housings
3)	Transport direction of longitudinal conveyor section
4)	Transport direction of transverse conveyor section

The electrical transverse conveyor EQ 1/TR is used for connecting two parallel longitudinal sections with a small section gap a.

It is also suitable for use in ESD applications.

Accumulation operation is not permitted.

Energy efficiency – Rexroth 4EE

Circuit diagram for unit with pneumatic equipment for two positions PN = 2

1)	Not included in the scope of delivery

Circuit diagram for unit with pneumatic equipment for three positions PN = 3

1)	Not included in the scope of delivery

No.			3842998012
Max. total weight of workpiece pallet	mG	kg	3
ESD			yes
Cleanroom class			ISO class 7
Dry room	r.F.	%	<1
Reversible operation			permitted
Required compressed air connection	p	bar	4 ... 6 bar
Pneumatic push-in fitting	Ø	mm	4