Attributes
| Condition on delivery |
Assembled |
| ESD |
Yes |
| Gross weight |
4.2kg |
| Height |
118mm |
| Length |
164mm |
| Material information |
Housing: aluminum; hard anodized,Latch: steel |
| Maximum permissible mass workpiece pallet mG at nominal speed vN 12 m/min |
110 kg |
| Maximum permissible mass workpiece pallet mG at nominal speed vN 15 m/min |
100 kg |
| Maximum permissible mass workpiece pallet mG at nominal speed vN 18 m/min |
100 kg |
| Maximum permissible mass workpiece pallet mG at nominal speed vN 6 m/min |
130 kg |
| Maximum permissible mass workpiece pallet mG at nominal speed vN 9 m/min |
110 kg |
| Min. workpiece pallet weight m |
15 kg |
| Net weight |
4.2kg |
| Operating temperature [T] max |
60 °C |
| Pneumatic circuit diagram |
1 Not included in the scope of delivery |
| Pneumatic straight connection [Ø] |
6mm |
| Recommended accessories |
Sensor M12x1 with rated switching distance SN = 4 mm, overall length 45 mm,Clamping holder |
| required compressed air connection [pmax] |
6bar |
| required compressed air connection [pmin] |
4bar |
| Scope of delivery |
Incl. fastening material for installation on conveyor section,Right-angle connector for the push in air connections,Position sensing |
| Weight |
4.2kg |
| Width |
181mm |
| Workpiece pallet weight [mG] |
130kg |
- Stopping on the outside of the frame module
- Can be used in reversible operation
- Design permits installation with a section gap from a = 90 mm when space is limited
- Suitable for mounting on an ST 2/… section with a profile width of 45 mm or an ST 2/…-H section with a profile width of 50 mm
- 4 positions can be moved to pneumatically: upper, lower position and stop rail in the extended and retracted state
- 3 positions can be detected: top, bottom and retracted stop rail
- Additional possibilities for installing sensors, advantageous in restricted conditions
- Can be combined with WT 2 and WT 2/F
- Notice: Combination with WT 2/LS not possible
- The slide stop is used in a transverse section that connects more than two longitudinal sections and that requires supplementary stops
- A lift transverse unit can feed in the workpiece pallet onto the longitudinal section when the slide stop is activated
- When depressurized, the pneumatically adjustable slide stop is extended to the upper end position
- Mounted inside the tracks, directly on the conveyor section
- - Stopping on the outside of the frame module
- - Can be used in reversible operation
- - Design permits installation with a section gap from a = 90 mm when space is limited
- - Suitable for mounting on an ST 2/… section with a profile width of 45 mm or an ST 2/…-H section with a profile width of 50 mm
- - 4 positions can be moved to pneumatically: upper, lower position and stop rail in the extended and retracted state
- - 3 positions can be detected: top, bottom and retracted stop rail
- - Additional possibilities for installing sensors, advantageous in restricted conditions
- - Can be combined with WT 2 and WT 2/F
- - Notice: Combination with WT 2/LS not possible
- - The slide stop is used in a transverse section that connects more than two longitudinal sections and that requires supplementary stops
- - A lift transverse unit can feed in the workpiece pallet onto the longitudinal section when the slide stop is activated
- - When depressurized, the pneumatically adjustable slide stop is extended to the upper end position
- - Mounted inside the tracks, directly on the conveyor section
Slide stop VA 2/D-130
Slide stop, can be lowered pneumatically, dampened stop
Stopping on the outside of the frame module, Can be used in reversible operation, Design permits installation with a section gap from a = 90 mm when space is limited, Suitable for mounting on an ST 2/… section with a profile width of 45 mm or an ST 2/… H section with a profile width of 50 mm, 4 positions can be moved to pneumatically: upper, lower position and stop rail in the extended and retracted state, 3 positions can be detected: top, bottom and retracted stop rail, Additional possibilities for installing sensors, advantageous in restricted conditions, Can be combined with WT 2 and WT 2/F, Notice: Combination with WT 2/LS not possible, The slide stop is used in a transverse section that connects more than two longitudinal sections and that requires supplementary stops, A lift transverse unit can feed in the workpiece pallet onto the longitudinal section when the slide stop is activated, When depressurized, the pneumatically adjustable slide stop is extended to the upper end position, Mounted inside the tracks, directly on the conveyor section