BASE UNIT 65+ AL CONNECT DIR.
| Actual chain length | 151m |
| Delivery information | Fully assembled |
| Effective sliding rail length | 4x 0,2 |
| Height | 485.4mm |
| Length | 814mm |
| Material information | Housing: Diecast aluminum, powder-coated,Chain wheel: PA,Chain guide: PA,Hexagonal shaft up to size 160: PA, from size 160: Non-rusting steel 1.4301 + PA,Connector: Steel, galvanized,Ball bearing: Non-rusting steel 1.4301/FDA |
| Required accessories | Drive kit,Active bridge or passive bridge,Slide rail: Length calculation |
| Scope of delivery | Incl. fastening material |
| Size [b] | 65 |
| Weight | 10.22kg |
| Width | 68mm |
- Base unit connection drive + drive kit + active or passive bridge = a complete connection drive
- Reduced noise emission due to slide rails guided in the connection drive
- Installation of the drive kit possible on the right/left (motor, coupling, flange)
- Drive of a parallel conveyor section or bridge using a hexagonal hollow shaft integrated as standard
- Ball bearing made of non-rusting steel (1.4301), with seal on both sides and FDA-compliant grease filling
- Side elements with slot to attach holders for lateral guides, or similar
- 1 - Base unit connection drive + drive kit + active or passive bridge = a complete connection drive
- 2 - Reduced noise emission due to slide rails guided in the connection drive
- 3 - Installation of the drive kit possible on the right/left (motor, coupling, flange)
- 4 - Drive of a parallel conveyor section or bridge using a hexagonal hollow shaft integrated as standard
- 5 - Ball bearing made of non-rusting steel (1.4301), with seal on both sides and FDA-compliant grease filling
- 6 - Side elements with slot to attach holders for lateral guides, or similar
Ball bearing made of non rusting steel (1.4301), with seal on both sides and FDA compliant grease filling, Installation of the drive kit possible on the right/left (motor, coupling, flange), Drive of a parallel conveyor section or bridge using a hexagonal
Slide rail
Slide rail
Easy assembly - simply clip onto the section profile Secured against axial shifting due to lateral boltingCAD data
Drive kit
Drive kit
The adjustable ball catch coupling is protected and integrated in the flange to save spaceCAD data
Connection kit active bridge, connection kit passive bridge
Connection kit active bridge, connection kit passive bridge
Simple transmission of the drive force using hexagonal hollow shafts integrated into the base unit or return unit as standard Can be retrofitted into a standard configuration at any time Active and passive bridges can be used at section ends for product transferCAD data
Base unit connection drive AL
Note: High-pressure cleaning of the ball bearings is not permitted.
The connection drive is used for driving the conveyor chain in circuit systems with a top-running chain. The basic unit is quickly turned into a connection drive with variable mounting position by adding a drive kit. To transfer the conveyed goods, an active (A) or passive bridge (B) must be added. The active bridge (A) is driven by a transmission from the connection drive
Size: 65, 90 Suitable chain types: flat conveyor chain, static friction chain Permissible chain tensile force: Fmax = 1250 N Section length: L ≤ 30 m Conveying speed: vN = 4 ... 27 m/min, other speeds available on request Chain bag to compensate for chain elongation during service life Recommendation: No accumulation operation up to 1500 mm after the connection drive For safety reasons, only use with a closed profile Reversible operation not permitted Not permitted for wet operation or rough ambient conditionsInnovative drive concept
Conveyor noise level
Combination matrix
|
Straight |
Curves |
Drives |
Return Unit |
||||||||||||
|
Section profile AL open |
Section profile AL closed |
Assembly module |
Curve wheel |
Roller curve* |
Horizontal sliding curve |
Vertical curve |
Head drive |
Curve wheel drive |
Connection drive |
Center drive (STS)** |
Basic unit |
90° (STS)** |
Transmission kit |
||
|
Straight |
Section profile AL open |
J |
|||||||||||||
|
Section profile AL closed |
J |
J |
|||||||||||||
|
Assembly module |
J |
J |
N |
||||||||||||
|
Curves |
Curve wheel |
J |
J |
L2) |
L2) |
||||||||||
|
Roller curve* |
J |
N |
J |
N |
L1) |
||||||||||
|
Horizontal sliding curve |
J |
J |
J |
J |
N |
L1) |
|||||||||
|
Vertical curve |
J |
J |
J |
J |
L1) |
L1) |
L1) |
||||||||
|
Drives |
Head drive |
J |
J |
L2) |
L2) |
L1, 4) |
L1) |
L1, 4) |
N |
||||||
|
Curve wheel drive |
J |
J |
L2) |
L2) |
N |
L1) |
L1) |
N |
N |
||||||
|
Connection drive |
J |
J |
L2) |
L2) |
N |
L1) |
L1) |
N |
N |
N |
|||||
|
Center drive (STS)** |
L5) |
L5) |
L2, 5) |
L2, 5) |
N |
L1, 5) |
L1, 5) |
N |
N |
N |
N |
||||
|
Return Unit |
Basic unit |
J |
J |
L2) |
L2) |
L1, 4) |
L1) |
L1, 4) |
L2) |
N |
N |
L2, 3) |
L2, 3) |
||
|
90° (STS)** |
L5) |
L5) |
L2, 5) |
L2, 5) |
N |
L1, 5) |
L1, 5) |
N |
N |
L2, 5) |
N |
N |
L2) |
||
|
Transmission kit |
N |
N |
N |
N |
N |
N |
N |
J |
N |
J |
N |
J |
N |
N |
|
|
J |
possible without restrictions |
* Support profile must project 76+2 mm into the roller curve. |
|||||||||||||
|
L |
possible with restrictions |
** AL-STS adapter included in the scope of delivery. |
|||||||||||||
|
N |
not possible |
||||||||||||||
| 1) | Profile connector not required |
| 2) | Use of a profile piece (Lmin = 120 mm) |
| 3) | Assembly module required |
| 4) | For sizes 160-320: shorten the support rail on the dotted line |
| 5) | Use of the AL-STS adapter |
Request Quote
How to Find Us
If you have any questions, just fill in the contact form, and we will answer you shortly. If you are living nearby, come visit us.